FLUKE-N5K 3PP50I

ราคา 670,100.00.-

จำนวนสินค้า

สินค้าหมด

TRIPLE E TRADING CO., LTD.

นำเข้า และ จำหน่ายอุปกรณ์ไฟฟ้าในโรงงานทุกชนิด

เข้าชมร้านค้า

รายละเอียด

Norma High Precision Power Analyzers

Compact, high precision power analyzers – easy to carry and save working space
Simple user interface ensures easy, intuitive operation
Standard configurations allow users to specify the exact functionality required for their own unique application
Accurately display dynamic events on all phases at exactly the same point in time with simultaneous parallel acquisition of all phases
All inputs are galvanically isolated to avoid short circuits in all applications.Voltage, current and power harmonics up to the 40th
FFT analysis, vector diagram display, recorder function and Digital Oscilloscope (DSO) mode included
User-selectable average time – from 15 ms up to 3600 s – for dynamic measurements
4 MB on-board memory for storage of measured values
RS232 and USB available as standard; optional IEEE 488/Ethernet available
Optional process interface available to measure torque and speed with external sensors; includes four analog outputs for easy use on motor and drive applications
341 kHz or 1 MHz sample rates for detailed signal analysis
Bandwidth from dc to 3 MHz / 10 MHz for reliable measurement precision
Includes Fluke NormaView PC software for setup, data download, analysis & report writing

Specifications
	Norma 4000		Norma 5000
Number of Phases	1 or 3		3, 4, or 6
Bandwidth	DC to 3 MHz or dc to 10 MHz depending on input module
Basic Accuracy	0.2%, 0.1% or 0.03% depending on input modules
Sampling Rate	0.33 MHz or 1 MHz depending on input modules
Voltage Input Range	0.3 to 1000 V
Current Input Range (direct, not via shunt)	0.03 mA – 20 A depending on input module
Display	Color, 5.7" / 144 mm - 320 x 240 pixel
Fast Fourier Transformation (FFT)	To the 40th harmonic
RS232 Interface	Standard
PI1 Process Interface (8 analog / impulse inputs & 4 analog outputs)	Optional
IEEE 488/GPIB Interface	Optional
Fluke NormaView PC Software (for data download, analysis & report writing)	Standard
Basic Function
Included functions	Fast Fourier Transformation (FFT) Digital Oscilloscope (DSO) Integration function (energy) Vector Display Recorder RAM data memory Configuration More information on the Basic Function of the Norma Series >>

Working Temperature Range	Non-gapping calculation of averaged values for each phase. In three phase system additionally calculation of total power and averaging of V and I of the three phases. The fundamental H01 will be calculated in synchronous mode also for these values. U_rms effective value, U_rm rectified mean, Um mean value Up-, Up+, U_pp peak values U_cf crest factor U_cf, U_ff form factor U_fc fundamental content U_thd distortion factor DIN, IEC I_rms effective value, I_rm rectified mean, I_m mean value I_p-, I_p+, I_pp peak values I_cf crest factor I_cf, I_ff form factor I_fc fundamental content I_thd distortion factor DIN, IEC P active power [W] Q reactive power [Var] S apparent power [VA] ë, cos. phase angular Integral function for active power P, reactive power Q, apparent power S, voltage (U_m) and current (I_m) Number of digits 4 or 5 dependent on measured value.
Frequency and Synchronization
Range	DC and 0.2 Hz to sample rate
Accuracy	±0.01 % of measured value (reading)
General Specifications	Channels which can be selected: all U/I or external input. One of three low pass filter with different frequencies can be switched into the signal. The frequency is always visible on the top of the screen. The BNC synchronization socket on backside of the instrument can be used either as input or output. The input signals can be measured up to the sample rate of the power phase. The maximum level must not be higher then 50V. The output signal is a pulsed 5Volts TTL signal (frequency depends on the measured synch frequency).
Power Phase Channels
Range	PP42	PP50	PP54	PP64
Accuracy	0.2% (0.1% rd + 0.1% rg)	0.1% (0.05% rd + 0.05% rg)	0.1% (0.05% rd + 0.05% rg)	0.03% (0.02% rg + 0.01% rg)
Current range	20A	10A	10A	10A
Sampling rate	341 kHz	1 MHz	341 kHz	341 kHz
Bandwidth	3 MHz	10 MHz	3 MHz	3 MHz
More info	More on PP42>>	More on PP50>>	More on PP54>>	More on PP64>>
Configuration Memory
Memory for Configurations	4 MB
	Up to 15 user configurations can be saved into a permanent memory and reloaded later on. Changes that were not saved are lost after switching off the instrument.
Memory for Settings	Standard
Ambient Conditions
Working Temperature Range	5°C to 35°C (41°F to 95°F)
Storage Temperature Range	-20°C to 50°C (-4°F to 122°F)
Housing Material	Fluke Norma Power Analyzers are extremely compact and equipped with a solid metal case to meet stringent EMC requirements.
Climatic Class	KYG DIN 40040, max. 85 % relative humidity, non-condensing.
Power supply	85 V ac to 264 V ac, 50 Hz to 60 Hz, dc 100 to 260 V, ca. 40 VA European plug with switch. Binding post for current available on some models.
Measuring Inputs	Safety sockets 4 mm, 2 for each input. External shunt connection over BNC socket.
Operation	Membrane keyboard with cursor – function keys and direct functions.
Connections	Rear panel of the 3-phase Analyzer
Standards and Safety
Electrical Safety	EN 61010-1 / 2nd Edition 1000 V CAT II (600V CAT III) Degree of pollution 2, safety Class I EN 61558 for transformer EN 61010-2-031/032 for accessories
Maximum inputs	For voltage inputs Measurement range 1000 V_eff, 2 kV_peak For current inputs Measurement range 10 A_eff, 20 A_peak
Test voltage
Net input case (protective conductor)	1.5 KV AC
Net connection Measurement input	5.4 kV AC
Measurement inputs Case	3.3 kV AC
Measurement input input	5.4 kV
Electromagnetic susceptibility
Emission	IEC 61326-1, EN 50081-1, EN 55011 Class B
Immunity	IEC 61326-1 / Annex A (industrial sector), EN 50082-1
Physical Dimensions
Size
Norma 4000	5.9 in x 9.3 in x 12.4 in (150 mm x 237 mm x 315 mm)
Norma 5000	5.9 in x 17.6 in x 12.4 in (150 mm x 447 mm x 315 mm)
Weight
Norma 4000	Approx. 11 lb. (5 kg)
Norma 5000	Approx. 15 lb. (7 kg)